Features * * * * * * Unregulated Converters High efficiency uo to 84% full load Low deviation (10% - 100% load) 1kVDC and 2kVDC isolation option UL60950-1 and EN/IEC60950-1 certified -40C to +100C operating temperature range 1W SIP7 package Description The RB/E series is an unregulated DC/DC converter in standard SIP7 package style. This series has been designed to offer exceptionally high efficiency at low loads, an extended operating temperature range and low deviation (10% to 100%). Uses include applications with restricted energy budget and industrial applications where a high efficiency level is required. DC/DC Converter RB/E 1 Watt SIP7 Single Output Selection Guide Part Number nom. Input Voltage [VDC] Output Voltage [VDC] Output Current [mA] Efficiency typ. (1) [%] max. Capacitive Load (2) [F] 3.3 5 200 83 2200 RB-3.305S/E (3,4) 5 5 200 84 2200 RB-1205S/E (3,4) 12 5 200 84 2200 RB-2405S/E 24 5 200 81 2200 RB-0505S/E (3,4) (3,4) Notes: Note1: Efficiency is tested at nominal input and full load at +25C ambient Note2: Max Cap Load is tested at nominal input and full resistive load and is defined as the capacitive load that will allow start up in under 1s without damage to the converter E358085 Model Numbering UL60950-1 certified CAN/CSA-C22.2 No 60950-1 certified EN60950-1 certified IEC60950-1 certified RB- __ 05S/E nom. Input Voltage Output Voltage Protection (3) Isolation Option (4) Single Notes: Note3:standard part is without continuous short circuit protection add suffix /P" for continuous short circuit protection Note4: add suffix /H" for 2kVDC isolation or add suffix /HP" for 2kVDC isolation and continuous short circuit protection Ordering Examples: RB-1205S/E: 12VDC Input Voltage, 5VDC Output Voltage, Single Output RB-3.305S/EP: 3.3VDC Input Voltage, 5VDC Output Voltage, Single Output with continuous short circuit protection RB-0505S/EH: 5VDC Input Voltage, 5VDC Output Voltage, Single Output with 2kVDC isolation RB-0505S/EHP: 5VDC Input Voltage, 5VDC Output Voltage, Single Output with 2kVDC isolation and continuous short circuit protection www.recom-power.com REV.: 1/2018 ECO-1 RB/E DC/DC Converter Series Specifications (measured @ Ta= 25C, nom. Vin, full load and after warm-up otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Internal Input Filter type Input Voltage Range 10% Start-uo time 250ms 0% Minimum Load Internal Operating Frequency (5) 20kHz Output Ripple and Noise 90kHz 20MHz BW 50mVp-p 100mVp-p Notes: Note5: Operation below 10% load will not harm the converter, but specifications may not be met Efficiency vs. Load RB-xx05S/E 100 90 Efficiency [%] 80 70 60 50 40 30 3.305 0505 1205 2405 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] REGULATIONS Parameter Condition Value Output Accuracy 5.0% max. Line Regulation low line to high line 1.2% max. Load Regulation 10% to 100% load 12.0% typ. Tolerance Envelope Output Voltage [%] +10% +5% Typical L o +5% ad Line Vnom -2% -5% 10 50 100 Output Load [%] continued on next page www.recom-power.com REV.: 1/2018 ECO-2 RB/E DC/DC Converter Series Specifications (measured @ Ta= 25C, nom. Vin, full load and after warm-up otherwise stated) Deviation vs. Load RB-xx05S/E 25 3.305 0505 1205 2405 20 Deviation [%] 15 10 5 0 -50 -10 0 10 20 30 40 50 60 70 80 90 100 Output Load [%] PROTECTIONS Parameter Type Value without suffix With suffix "/P" Short Circuit Protection (SCP) 1 second continuous without suffix tested for 1 second rated for 1 minute 1kVDC 500VAC with suffix "/H" tested for 1 second rated for 1 minute Isolation Resistance 2kVDC 1kVDC 10G min. Isolation Capacitance 75pF max. Isolation Voltage (6) I/P to O/P Insulation Grade basic Notes: Note6: For repeat Hi-Pot testing, reduce the time and/or the test voltage Note7: Refer to local wiring regulations if input over-current protection is also required. Recommended fuse: T1A slow blow type ENVIRONMENTAL Parameter Operating Temperature Range Condition Value full load @ free air convection (see graph) Operating Altitude Operating Humidity -40C to + 100C 2000m non-condensing 95% RH max. Pollution Degree MTBF PD2 according to MIL-HDBK-217F, G.B. +25C +100C 3459 x 10 hours 756 x 103 hours 3 continued on next page www.recom-power.com REV.: 1/2018 ECO-3 RB/E DC/DC Converter Series Specifications (measured @ Ta= 25C, nom. Vin, full load and after warm-up otherwise stated) Derating Graph (@ free air convection) 100 90 Output Load [%] 80 70 60 50 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 Ambient Temperature [C] SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report / File Number Information Technology Equipment, General Requirements for Safety 1602031 Information Technology Equipment, General Requirements for Safety E358085-A4-UL EAC RU-AT.49.09571 RoHs 2+ Standard IEC60950-1:2005, 2nd Edition + A2:2013 EN60950-1:2006 + A2:2013 UL60950-1, 2nd Edition:2007 CAN/CSA C22.2 No. 60950-1-03, 2nd Edition:2007 TP TC 004/2011 RoHS-2011/65/EU + AM-2015/863 DIMENSION AND PHYSICAL CHARACTERISTICS Parameter Type Value Material case potting PCB non-conductive black plastic (UL94 V-0) epoxy, (UL94 V-0) FR4, (UL94 V-0) Dimension (LxWxH) 19.6 x 6.0 x 10.2mm Weight 2.2g typ. continued on next page www.recom-power.com REV.: 1/2018 ECO-4 RB/E DC/DC Converter Series Specifications (measured @ Ta= 25C, nom. Vin, full load and after warm-up otherwise stated) Dimension Drawing (mm) embossed logo 19.6 10.2 6.0 Pinning information Pin # 1 2 4 5 6 0.50 Marking 2.00 4 5 6 5x2.54= 12.70 4.10 Recommended Footprint Details 1.00 O +0.15/-0 2.54 Bottom View 1 2 0.250.05 1.27 0.51+0.10/-0.05 1 2 Single +Vin -Vin NC -Vout +Vout NC = no internal connection Tolerance: xx.x= 0.5mm xx.xx= 0.25mm 4 5 6 Top View 2.54 PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) tube 520.0 x 16.0 x 9.0mm Packaging Quantity tube Storage Temperature Range 25pcs -55C to +125C Storage Humidity 95% RH max. The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM's explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 1/2018 ECO-5